the_tool_man
Latest activity Postings About
-
-
the_tool_man replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.Yeah, that makes sense. RA didn't have OEM, so I ordered one from a dealer. Paid a little more, but I only want to dig into it once. -
the_tool_man reacted to Geotrash's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with
Like.
I just did mine yesterday on my ‘07 but mine has the block off plate instead of cooler lines - also AWD. The job is a lot easier with a... -
the_tool_man reacted to t_bergman's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
Since it's the steering column and that uses plastic components that I don't want to break or have to also replace, if it were me I'd...
-
the_tool_man replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.I changed my oil and emptied the catch can last night. I used my new HF ramps, which worked great. Last change I sprayed off the...
-
the_tool_man replied to the thread Does any use a Fumoto oil pan drain valve?.It's hard to say. But I'd speculate the difference is insignificant, or they wouldn't recommend it. If you think about it, some amount...
-
the_tool_man replied to the thread Does any use a Fumoto oil pan drain valve?.I changed my oil last night, and on a whim, removed the valve to see how much more would drain out. It was probably less than 4 ounces.
-
the_tool_man reacted to Fless's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
For a 2008 Tahoe: (https://www.gmpartsdirect.com/v-2008-chevrolet-tahoe--ls--5-3l-v8-gas/body--cowl)
-
the_tool_man reacted to Doubeleive's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
no they are different, one side is wider than the other, silverado/sierra's have them as well also different.... on the bottom both...
-
the_tool_man replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.Sorry I wasn't clear. While multi-material 3D printing is possible, I was thinking of a single non-flexible part that replaces the OEM...
-
the_tool_man replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.Mine are rotted, too. I'm not happy to pay $140 to replace them. The gap seems unnecessarily large for the hood hinge to pass through...
-
the_tool_man reacted to 89Suburban's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
-
the_tool_man reacted to gooffeyguy's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
My rubbers that surround the hinges are cracked, but I'm not spending $70 to replace each of them. I did get a box of these Cerakote...
-
the_tool_man reacted to j91z28d1's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
how does it look with them completely removed? I mean they don't really seem to be doing anything but rotting away haha. if they can be...
-
the_tool_man reacted to Doubeleive's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
I haven't searched for any yet, I replaced the end caps with new OEM around the hood hinge as the rubber rot's, those are pricey around...
-
the_tool_man reacted to RooTBeeRthe1st's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
Another fun one. During the morning commute I started hearing a noise, couldn't tell what is was. On the way home, it got much...
-
-
Loading…
-
Loading…
