Search results

  1. Erickk120

    50mph+= Brake/ABS light "service brake system" Speedo goes up and down roughly +7 -7 mph erratically

    As the title reads, lately I noticed after passing 50+ mph my speedo jumps up and down +7-7 mph and it triggers my abs and brake light as soon as it does it, along the message "service brake system." Speedo acts normal under that speed, but as soon as I go a touch over 50 it goes up and down...
  2. Erickk120

    4l60E to NV3500 5 speed 04 Tahoe

    I know there are several of these around but I'd thought I'd post some of my progress with mine so far. My build is more or less budget oriented and I still have a few things left to do. So far I will post a summary on where I stand currently. So far if I'm being honest the hardest part of the...
  3. Erickk120

    Dorman stamped AAM DS slip yoke

    This will be both a life ramble and a question, let me start by saying I've been gone for the past year or so due to the fact the fat lady has been down for said amount, and I had lost all the will power to wrench on it. So fast forward 1 year and a half and I decided to slowly get back to...
  4. Erickk120

    Help with an Np241c front sensor 2 vs 3 pin question

    For those of you 98 and below with an np241c, do you guys have a 2 pin or a 3 pin for that front sensor, I'm working on a swap atm, I got a 95 241c with a 3 pin connector at the front by the shift lever, and I need the pig tail, but from the salvage yards I've only managed to find 2 pinners. I...
  5. Erickk120

    Tcase on its way out?

    So Started noticing this clunk lately its almost as if you are going into 4low when I cycle between R and D and vice also its the same sound when I gun it at high speed. I had another thread but it was regarding a vibration that started recently. Also noticed the rear tcase started leaking...
  6. Erickk120

    Slack on/play on slip yoke

    Just a few questions for you 4wd guys, Do you have slack on your slip yoke when you gas it at high speeds? By that I mean, lets say you are cruising at 70 mph then you let off and then you just stab the gas do you get a clunk? I've started noticing this but I cant remember if it was there...
  7. Erickk120

    Pulling left after new alignment

    Just curious if anybody has any experience with alignment specs/settings. I had my truck realigned because I noticed the right tire was getting an outer rub like contact. Got it there got it done, afterwards i started noticing that when i drive on the left most lane, with a crown bias on the...
  8. Erickk120

    Knock sensors

    Hello everyone, I dropped my tranny for minor work on it, and while I was in there I decided to replace the rear main seal and cover gasket. While they leaked it wasn't as bad as I expected, the main seal was leaking a bit from the lower portion, and the cover was also leaking a tiny amount...
  9. Erickk120

    Can I drop the tranny without a tranny jack/adapter?

    I'm planning to use one of my flat floor jacks with some form of wood base and a ratchet to secure the 4l60e. I was wondering if I can get away without buying an adapter with angle adjuster, and instead just place it on a flat base/ratchet strap and try to pull it out, or is there a lot of...
  10. Erickk120

    IFS stubby axle sleeve?

    I was doing my axle seals today and found out both seal surfaces are pitted, I was wondering if anyone knows if they make redi sleeves for these or if I'm screwed. I've looked for a bit and can't seem to find them. Thanks
  11. Erickk120

    Possibly bad hub bearing?

    I won't have time to look into it till Sunday but I think the one OEM hub bearing is finally showing some signs of early wear. When I accelerate past 30 mph I hear a lot of wind noise, more than usual, it sounds like tire noise if that makes sense just louder than usual, well that was the last 2...
  12. Erickk120

    Tracking mysterious single pop/clunk SOLVED

    rebuilt entire front end aside from, CV axles/Hubs, as they were tight and had no play in any axis, I even did control arm bushings and camber/caster kits. Lower control arms look fine, I've gone back and retightened just about everything to spec, I even torqued the front and rear cross member...
  13. Erickk120

    Alignment from hell rant

    Finally had the time to get an alignment to start using my truck again, my wheel was about 15 degrees to the right before getting it done, I forgot to mention this as I figured they would correct it with the right alignment. Surprise they didn't. Oh well, no big deal right, well I wish that was...
  14. Erickk120

    Dreaded service brake system message

    I recently replaced my entire suspension, kept the old hub bearings since those have around 50k miles. now brake related I replaced an old cracked line in the driver side and readjusted the pistons back to their resting place to service the guide pins and lube the hardware brake pads are also in...
  15. Erickk120

    Suspension overhaul recommendations

    Hey, I'm planning to replace my outer tie rods, stabilizer linkages, balls joints, and shocks, in my Z71. I was thinking of going with Moog ball joints, but I also caught some Ac delco's that are half the price. The moog ones are roughly 38-40 a pop, while the ac delco ones seem to be around 21...
  16. Erickk120

    Coolant leak, rear engine area

    Hello guys first time here, came over from ls1tech I have an 04 tahoe with 214k miles I changed my oil pan gasket today and noticed There was coolant in the top of the tranny oil pan front area, note this is only the passenger side, it gets there through the outside transmission oil dipstick...

Forum statistics

Threads
129,120
Posts
1,810,776
Members
92,207
Latest member
2DoeProjectHoe

Latest posts

Top