Search results

  1. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I have a Corsa catback on my 06 Denali and I love it! Sent from my iPhone using Tapatalk
  2. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    ^^^X2 Sent from my iPhone using Tapatalk
  3. rpdnali

    Custom headliner mods...?

    I would get the liner for one without the sunroof and cut it out where you need it. Sent from my iPhone using Tapatalk
  4. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Which taillights did you go with? any pics?
  5. rpdnali

    Sway bar help!

    LOVE my djm's!!
  6. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Pulled rtd fuse and fixed the service air ride message. It still drives normal after removal!
  7. rpdnali

    Mileage on 2000-2006 Denali's

    2006 with 96k. Only issue I have had was the air ride and I lowered and replaced the air shocks with Belltech shocks.
  8. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Replaced low beam bulbs with silver star ultras (one was bad), and fixed seats so they will lay back farther.
  9. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Drove her to work in the snow the last two nights.
  10. rpdnali

    NC

    Raleigh
  11. rpdnali

    Service Ride Control

    not difficult...just looking for suggestions. Thanks. not going back so I'll just cut'em, solder, and heat shrink.
  12. rpdnali

    Service Ride Control

    resistors came in finally. I noticed that they have short leads on them. I figured I would just stick the leads in the holes in the connector (and solder) but the leads are too short. How do I go about hooking them up? The obvious answer is to cut the connector off and solder the wires...
  13. rpdnali

    What's a black 06 Denali with 89K and factory 20s worth in excellent condition?

    Nice ride! I purchased mine in August. It has Nav and sunroof but no 20's. It had 87k on the ticker. I paid 14.5k for it (has a few minor cosmetic flaws and needed two tires). If I'm not mistaken the NADA on it was close to 19k and the kbb was around 17ish. I would definitely start north...
  14. rpdnali

    Lowered pic

    Thanks for the props! Still in progress...
  15. rpdnali

    Lowered pic

    Thanks! I love it! I think my favorite thing about it is the 6.0L engine. Plenty of HP!
  16. rpdnali

    Lowered pic

    I did not remove them. I cut the factory stops and its not sitting on them. I only did the 3" drop. I initially put the springs in without the spacers and the panhard bar was close to the exhaust. So, I decided to see what it looked like with the spacer and I'm ok with it. When I get a...
  17. rpdnali

    Lowered pic

    Well, if the resistors don't fix it I will try the fuse and see how it handles. If I don't like the way it handles then I'll just have the error flash at me when I crank the truck....
  18. rpdnali

    Lowered pic

    Thanks! I haven't measured but on a level surface it looks closer to even between front and back. My driveway slopes a little. I do have the 1" spacer in the rear though. I was initially going without it but I think I will have clearance issues with the exhaust....The resistors will just...
  19. rpdnali

    Lowered pic

    Sorry for the dirty pic. Its the only one I have since I finished up. 2" BT drop spindles, new upper and lower ball joints and tie rod ends, BT shocks all around, shock extensions, BT springs, DJM front and rear sway bars and new endlinks. All in all it was not too bad....when I had...
  20. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Oil sensor changed out and gauge reading correctly again!
  21. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Removed the cross bars from the roof rack. Gonna run to parts store to pick up an oil pressure sending unit and change it out. Needs washing but its too cold!
  22. rpdnali

    Service Ride Control

    Awesome! Thanks!
  23. rpdnali

    Service Ride Control

    I went to Radio Shack today and all they had were 1/8,1/4,1/2 and 1 watt resistors. I am assuming by 25 watt you mean .25watt (1/4)? The only 3.9 ohm resistors they had were the 1/2 watt. What should I use?
  24. rpdnali

    Anyone in the INDY area with a 2/3 drop??

    Just finished mine up on my 06 Denali. It rides as good and handles like a performance car.
  25. rpdnali

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Finally finished up replacing suspension. 2" bt drop spindles in front, 4" lowering springs in rear (with spacer for 3" drop), bt shocks all around, front and rear DJM sway bars, new moog ball joints, new moog outer tie rod ends....think that's about it. Gonna wait and see how it settles out...

Forum statistics

Threads
129,179
Posts
1,811,762
Members
92,275
Latest member
DP2024

Latest posts

Top