Disable auto-dimming? (ambient light sensor)

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

mikez71

Full Access Member
Joined
Mar 9, 2023
Posts
770
Reaction score
890

The problem:

When I'm in daytime shade, the dash is dimmed. Takes about 20 seconds after pulling into direct sunlight before the dash finally brightens. Need to bypass dimming so it turns on with headlights only..

Sounds like a simple resistor won't cut it. Anyone have some ideas? I'll eventually pull the sensor to see what happens..
 
Last edited:
OP
OP
mikez71

mikez71

Full Access Member
Joined
Mar 9, 2023
Posts
770
Reaction score
890

According to that link, grounding the sensor wire should keep dash bright.. Looking at out wiring diagrams, it's a white wire that goes to BCM X2(J2?) pin 11. Ground is a white/black wire.

Have it disconnected, don't see any white goop. Sunload sensor wiring is L-BU/BK and GY
Might wire a relay powered by headlight output to connect ambient sensor.. no headlight have it go through 600ohm resistor mentioned in the first post link.
 
Last edited:

swathdiver

Full Access Member
Joined
May 18, 2017
Posts
19,148
Reaction score
25,179
Location
Treasure Coast, Florida
Do you have a dash mat or something obstructing the sensor? Mine switches pretty quick even with the dash mat around it. The sensors are very reliable but have seen them wear out over the years.
 
OP
OP
mikez71

mikez71

Full Access Member
Joined
Mar 9, 2023
Posts
770
Reaction score
890
No dashmat. Probably should try a new sensor, don't want to add wiring for something like this. I don't notice it that often, relatively minor annoyance, but I am hoping it's one of the last little electrical "fixes" I will make to this truck..

Disconnected sensor and backlighting is daylight bright.(makes sense safety wise) Dimmer circuit will not adjust instrument/radio display backlighting, but still adjusts switch backlighting.
 

Airman68

Member
Joined
Jul 26, 2022
Posts
74
Reaction score
125
Location
Kaukauna, WI
Mine seems to be "lazy". Takes a long time once outside to brighten up. Somtimes while driving, it dims the dash lights for no reason. Wonder if I should just change the sensor??
 
OP
OP
mikez71

mikez71

Full Access Member
Joined
Mar 9, 2023
Posts
770
Reaction score
890
Somtimes while driving, it dims the dash lights for no reason.
That's what gets to me. Even if there is a reason (tunnel/trees) I do not want it dimmed in daytime! Still hoping to bypass, but I haven't worked on it lately as I am trying to glue the cracked dash together.. Using lots of JB weld..

BTW what year is yours? I've seen posts about white goo inside the sensor, doesn't look like it's in mine, but maybe I need to take it apart to see it..
 
Last edited:

Scott in AZ

Full Access Member
Joined
Mar 23, 2023
Posts
190
Reaction score
335
Location
Arizona
My ambient sensor is failed so my headlights are on all the time, and DRL are never on. I’m getting psyched up to remove the dash, paint it with a Pewter refresh, and replace the ambient sensor.

I think if you ground out your sensor, your DRLs won’t work, and you’ll have same problem as I do.

Then the only other electrical gremlin I’ll have is the fuel gage. My level sensor is starting to fail. Fuel Gage measures accurately below 3/4 tank but intermittent goes to “E” empty when full. I’ve heard I need to replace the fuel pump to fix this.
 

Attachments

  • 9B5077B9-1FCD-4158-ABF6-7615A870579E.jpeg
    9B5077B9-1FCD-4158-ABF6-7615A870579E.jpeg
    180.9 KB · Views: 1

Foggy

Full Access Member
Joined
Jul 25, 2019
Posts
983
Reaction score
1,197
Location
KS
My ambient sensor is failed so my headlights are on all the time, and DRL are never on. I’m getting psyched up to remove the dash, paint it with a Pewter refresh, and replace the ambient sensor.

I think if you ground out your sensor, your DRLs won’t work, and you’ll have same problem as I do.

Then the only other electrical gremlin I’ll have is the fuel gage. My level sensor is starting to fail. Fuel Gage measures accurately below 3/4 tank but intermittent goes to “E” empty when full. I’ve heard I need to replace the fuel pump to fix this.
Try running 2 bottles (big ones) of Techron Fuel System Concentrate in
your next fill up. Might take 2 tries... This is pretty common on the early 2000+
GM stuff. Shit gets built up on the sending unit. Techron will fix it most of the time..
if it does, make sure to run the techron thru regularly (only use the black bottle that says
Concentrate) , the other ones suck
 

Scott in AZ

Full Access Member
Joined
Mar 23, 2023
Posts
190
Reaction score
335
Location
Arizona
Try running 2 bottles (big ones) of Techron Fuel System Concentrate in
your next fill up. Might take 2 tries... This is pretty common on the early 2000+
GM stuff. Shit gets built up on the sending unit. Techron will fix it most of the time..
if it does, make sure to run the techron thru regularly (only use the black bottle that says
Concentrate) , the other ones suck
Foggy if this works Ima’ come correct w you. Thanks already. I’ll give it a try and let you know.
 

Airman68

Member
Joined
Jul 26, 2022
Posts
74
Reaction score
125
Location
Kaukauna, WI
That's what gets to me. Even if there is a reason (tunnel/trees) I do not want it dimmed in daytime! Still hoping to bypass, but I haven't worked on it lately as I am trying to glue the cracked dash together.. Using lots of JB weld..

BTW what year is yours? I've seen posts about white goo inside the sensor, doesn't look like it's in mine, but maybe I need to take it apart to see it..
Mine is a 2008. Still trying to work out some bugs and this one bugs me...
 

Forum statistics

Threads
129,174
Posts
1,811,638
Members
92,266
Latest member
Mrjvieira

Latest posts

Top