Strengthening rear suspension for towing

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Yukonman209

TYF Newbie
Joined
Nov 18, 2022
Posts
7
Reaction score
5
Hello everybody just wondering I have a 2002 Yukon SLE 2 Wheel drive i’m using my Yukon to tow cars with a trailer by purchase. Just wondering how to make the suspension more stronger so the rear doesn’t drop as much when I hook up to the trailer with an a vehicle on it.7AAF3BFC-D676-497C-810D-8116C8C1C2BA.jpeg
 

swathdiver

Full Access Member
Joined
May 18, 2017
Posts
19,100
Reaction score
25,025
Location
Treasure Coast, Florida
Well, at about 21 years old, make sure the springs are not wore out and if they are replace them. Consider using air lift springs inside the coil springs or the Firestone or other similar "springs" that replace the jounce bumpers, aka bump stops.

Your rig calls for a weight distribution hitch with sway control. My old eyes can't see if you have one. If you don't, you need it.

Consider taking a load to your local CAT scales and moving the vehicle back and forth on the trailer to get an idea of where to place it for best stability and so as not to exceed your 1000 pound tongue weight rating.
 

Fless

Staff member
Super Moderator
Joined
Apr 2, 2017
Posts
10,246
Reaction score
20,306
Location
Elev 5,280
Shoot a pic of your RPO codes on the back of the glovebox lid and post it up here, but not at an angle like your first post. From that we can see what suspension came with your rig. You might have ZW7 (Premium Smooth Ride) and that has special rear shocks that adjust for loads. But we need to see those codes....

And let us see a picture of one of your rear shocks.
 
Last edited:

tungsten

Full Access Member
Joined
Sep 22, 2022
Posts
338
Reaction score
610
Ive only had air bags with leaf suspension,works really well.You could hook a 12v compressor into your trailer wiring to make filling easy.
 

MassHoe04

Full Access Member
Joined
Nov 4, 2021
Posts
1,586
Reaction score
2,796
Location
Western MA
Are you possibly loading too far up front or just towing vehicles that are too heavy?

Too far to the back will lift the back of the tow vehicle and cause instability and traction issues.

Too far to the front and your put too much weight on the tow vehicle.

Dead center is not good either. May cause stability issues with the trailer.

Ideally, load would start off with weight centered, then roll forward just a bit.

You are looking to put about 10% on the hitch for best handling and safest tow.

If this is a business for you, I saw these hitch weight scales. You could write-off the expense...
 
OP
OP
Y

Yukonman209

TYF Newbie
Joined
Nov 18, 2022
Posts
7
Reaction score
5
Shoot a pic of your RPO codes on the back of the glovebox lid and post it up here, but not at an angle like your first post. From that we can see what suspension came with your rig. You might have ZW7 (Premium Smooth Ride) and that has special rear shocks that adjust for loads. But we need to see those codes....

And let us see a picture of one of your rear shocks.
Can you give me a better idea where that code is that you’re talking about behind the glove box?
 

Fless

Staff member
Super Moderator
Joined
Apr 2, 2017
Posts
10,246
Reaction score
20,306
Location
Elev 5,280
So load leveling shocks. Can you take a pic that's more in line from front to back? What do the truck coil springs look like? See this driver's side pic for what the Nivomat shocks look like (you don't have those), and where the coil springs are on top of the axle.

Nivomat shock full.JPG

Here's what the RPO sticker looks like:

2004 Chevy Tahoe - Build Codes Glove Box_resized.jpg
 
Top