What did you do to your NNBS GMT900 Tahoe/Yukon Today?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Joined
Apr 11, 2018
Posts
6,284
Reaction score
12,260
Location
St. Louis
Finished, added about 2.5qts of fluid and all buttoned up and everything torqued to spec. That damn trackbar was a bit of a ***** to get the mounting holes lined up. It was very tight in the brackets. I did grease the bushings before trying. After a few cuss words and laying there contemplating the situation and what I had to work with I was able to use a big pry bar in certain locations to get it all lined up.

20220820_153435.jpg
 

89Suburban

Bull in the china shop
Supporting Member
Joined
Jan 10, 2013
Posts
12,850
Reaction score
35,204
Location
SE PA
Finished, added about 2.5qts of fluid and all buttoned up and everything torqued to spec. That damn trackbar was a bit of a ***** to get the mounting holes lined up. It was very tight in the brackets. I did grease the bushings before trying. After a few cuss words and laying there contemplating the situation and what I had to work with I was able to use a big pry bar in certain locations to get it all lined up.

View attachment 378481


Looks great man!!! Nice job!
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
23,408
Reaction score
34,034
Location
Stockton, Ca.
Finished, added about 2.5qts of fluid and all buttoned up and everything torqued to spec. That damn trackbar was a bit of a ***** to get the mounting holes lined up. It was very tight in the brackets. I did grease the bushings before trying. After a few cuss words and laying there contemplating the situation and what I had to work with I was able to use a big pry bar in certain locations to get it all lined up.

View attachment 378481
YEP
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
23,408
Reaction score
34,034
Location
Stockton, Ca.
Just got done looking at my passenger mirror motor. I pulled off the back cover and checked the wiring. When the fold button is pressed the mirror does nothing. No noise, no vibration, nothing. I pulled the plug going to the motor and connected a DVM to the 2 leads and set it to DC voltage. It was in auto mode and was reading very slight mV, but when I pressed the fold button the voltage would jump up into the 12v range for a second then go back down. So guessing it's a bad motor and not gear related.

I have to research what my options are here.
you could maybe find a used oem mirror on ebay a scratched up or damaged one and use it for parts
 

Rocket Man

Mark
Supporting Member
Joined
Dec 25, 2014
Posts
25,961
Reaction score
50,621
Location
Oregon
Finished, added about 2.5qts of fluid and all buttoned up and everything torqued to spec. That damn trackbar was a bit of a ***** to get the mounting holes lined up. It was very tight in the brackets. I did grease the bushings before trying. After a few cuss words and laying there contemplating the situation and what I had to work with I was able to use a big pry bar in certain locations to get it all lined up.

View attachment 378481
I think I used that same bolt kit. Looks great.
 

PG01

Supporting Member
Joined
Nov 6, 2016
Posts
14,731
Reaction score
17,778
Location
Up here to the right
Did the trans lines today, replaced the cooler too because why not…never and I mean never doing those lines again rotted right where GM put the little piece of plasticy wire loom crap to protect it from the diff or frame or whatever but it just made it rot out because of…. Northeast… (use your imagination) fell apart in my hands…. Cut that shit off the new line set…. What a pain in the d I c K … face full of rust and dirt …. Fun fun
Pic because….ya know
 

Attachments

  • 2E2A03B9-670A-41CF-B6CF-D034D8397E71.jpeg
    2E2A03B9-670A-41CF-B6CF-D034D8397E71.jpeg
    552.6 KB · Views: 8
  • 96ACE69E-5773-4FEE-BB50-D907C91FDE69.jpeg
    96ACE69E-5773-4FEE-BB50-D907C91FDE69.jpeg
    497.2 KB · Views: 8

swathdiver

Full Access Member
Joined
May 18, 2017
Posts
19,100
Reaction score
25,031
Location
Treasure Coast, Florida
Did the trans lines today, replaced the cooler too because why not…never and I mean never doing those lines again rotted right where GM put the little piece of plasticy wire loom crap to protect it from the diff or frame or whatever but it just made it rot out because of…. Northeast… (use your imagination) fell apart in my hands…. Cut that shit off the new line set…. What a pain in the d I c K … face full of rust and dirt …. Fun fun
Pic because….ya know
Glad to see you turn wrenches again Pete!
 

Charlie207

Full Access Member
Joined
Apr 13, 2021
Posts
1,168
Reaction score
2,129
Location
LFOD, New Hampshire
Did the trans lines today, replaced the cooler too because why not…never and I mean never doing those lines again rotted right where GM put the little piece of plasticy wire loom crap to protect it from the diff or frame or whatever but it just made it rot out because of…. Northeast… (use your imagination) fell apart in my hands…. Cut that shit off the new line set…. What a pain in the d I c K … face full of rust and dirt …. Fun fun
Pic because….ya know

Is yours 4x4?
Did you have to remove the cross-member to get those trans-cooler lines out? I spent a couple hours trying to get the old ones out, but couldn't wiggle them free.

Also, got a face full of rusty dirt, or was it dirty rust?
 

Forum statistics

Threads
128,790
Posts
1,805,486
Members
91,772
Latest member
dvnt
Top