6L80 Sonnax ZIP Kit, Pressure Switch rebuild, remote filter install, and fluid flush in 2013 Escalade ESV (Pic heavy)

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
Hello Gentlemen,

Over the past few days, I have completed the following work to the 6L80 transmission in my 2013 Escalade ESV:
-rebuilt the TECHM pressure switches using Sonnax parts
-installed most of the Sonnax ZIP kit in the valve body
-replaced the filter
-installed a new pan with a drain plug
-installed a remote spin on filter assembly
-flushed the fluid

I have had this new-to-me Escalade for two weeks tomorrow. I am catching up on maintenance and fluid changes that I feel need to be done. The truck has 124,*** miles on it, 1,000 of those I have put on.

I have a 'thing' for automatic transmissions, I want them to function as best as possible. This means lots of fluid changes for clean fluid, better filtration, and improvements from shift kits and such. This being a Cadillac, the transmission is tuned for softer shifts. I don't want softer shifts. I want positive shifts that will prolong the life of the transmission. (I will be putting in a Black Bear tune to improve the transmission shift characteristics as well.)


2021-10-24 020.JPG
4 gallons of Dexron VI, new transmission pan with nut and drain plug welded on, new GM filter, new GM TECHM solenoid filter plate, new GM heated oxygen sensor, new GM exhaust manifold to pipe seals, Sonnax ZIP kit, Sonnax pressure switch rebuild kit and tools, used remote oil filter mount with new filter, new Derale 3/8" ID transmission cooling hose, new WIX filter for the remote mount later.


Researching here on tahoeyukon forum, I have learned that the exhaust crossover pipe must be lowered to gain enough clearance to remove the transmission pan. From what I understand, there is no getting around this. So, I dropped the exhaust from the manifolds.


2021-10-24 009.JPG
Exhaust crossover pipe is tight up against the transmission pan.


This is a whole new world for me. I grew up in Ohio, and cut my teeth on 70's and 80's GM cars. They were all RUSTY! My Explorer was rusty. There is no way I would have been able to drop the exhaust without a cutting torch. On this Escalade, the only rust I have found is on untreated cast iron surfaces. I was able to remove the passenger's side upstream oxygen sensor with no fuss. I had to remove the oxygen sensor because 1) it blocked access to one of the exhaust manifold nuts, and 2) it needed to be replaced. I left the newly installed driver's side upstream oxygen sensor installed because it was not blocking any nuts and its cable had plenty of slack in it.

2021-10-24 007.JPG
Passenger's side upstream oxygen sensor blocking access to one of the exhaust manifold nuts.


2021-10-24 003.JPG
Driver's side upstream oxygen sensor is not blocking anything. Note the drops of AeroKroil on the end of the exhaust manifold studs.


I was able to break loose all of the exhaust manifold nuts with no real problem. NOTE: I had been soaking the nuts with AeroKroil for a week just in case. I had to get creative with a deep well 15mm socket, 15mm flare crow's foot, a universal joint, and lots of extensions. That, and I did have to disconnect the front drive shaft from the front axle and move it aside to get my fat hands up to the manifold nuts. With the nuts off, the exhaust dropped enough that it looked like I would be able to pull the transmission pan.


2021-10-24 014.JPG
Front drive shaft makes it tough to get my fat hands up there.
 
Last edited:
OP
OP
skpyle

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
2021-10-24 016.JPG
I unbolted the U-joint, pulled the shaft back to compress the rear joint, and then moved the shaft towards the engine to get more clearance. (Ignore the dripping oil filter. The selling dealership screwed up installing the oil filter. I fixed that after this work.)


2021-10-24 017.JPG
Clearance at the driver's side exhaust manifold after dropping the exhaust. This matters for installing the new seals later.


2021-10-24 018.JPG
Clearance at the passenger's side manifold with the exhaust dropped.


2021-10-24 019.JPG
Clearance at the transmission pan with the exhaust crossover pipe lowered.


Having taken my fair share of ATF showers in the past, I try to avoid that nowadays. I sucked as much fluid out of the transmission pan as I could get with my vacuum extractor. Hose down the dipstick and pump up the vacuum. Taking a trick from others here on the forum, I lowered the edge of the pan, then sucked out as much fluid as I could from the edge of the pan. Meaning I didn't spill or wear any ATF removing the pan.

I removed maybe 5 qts. The fluid was red, but not really clear. Which I expected.


2021-10-24 029.JPG
My vacuum fluid extractor.
 
OP
OP
skpyle

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
2021-10-24 030.JPG
Sucking fluid out of the transmission pan via the dipstick tube.


2021-10-24 032.JPG
Fluid was dark red. But not brown. Or black. Or chunky.


I was very relieved to find the pan clean. There was only a film of material on the bottom, and not alot of sludge on the magnet. The reusable gasket was fine, as well.


2021-10-24 037.JPG


I removed the fluid filter to expose the valve body. The ATF shower I avoided earlier was waiting on me. The service manual via AllData.com said to pull straight down, and not to twist the filter body. Which is what I did. Which is why it suddenly popped free and rotated, slinging fluid at me until I could toss it in the drain pan. Grrrr...
This is why I bought several rolls of shop towels for this job. I always make a mess doing fluid work.


2021-10-24 042.JPG
Fluid filter of doom...


2021-10-24 043.JPG
Valve body, with the TECHM in the upper foreground.
 
OP
OP
skpyle

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
There is a gotcha waiting for the unprepared. Both the service manual, and the Sonnax ZIP kit instructions state the six bolts that secure the valve body to the transmission case have an EP10 Torx Plus head. The service manual calls for this: DT-48285 - Valve Body Torx Plus Socket. I cross referenced it and bought this from Amazon:

https://www.amazon.com/dp/B007RKOAM0?psc=1&ref=ppx_yo2_dt_b_product_details



2021-10-24 040.JPG
EP10 Torx Plus socket from Amazon.


Even with the correct socket, the heads of the bolts are shallow. You really have to keep the socket on there straight and tight. Once I had the bolts out, I couldn't get the valve body out. It swung down at the front, but felt like it was hung up at the back. I had pulled the white plastic latch down to release the electrical connection. I put a couple of bolts back in and hit the internet. After a couple of youtube vidoes, I found you have to pull the valve body forward as you drop it to pull it out of the electrical connection. This would have been a good thing for the service manual to mention...


2021-10-24 120.JPG
This is the white latch that must be pulled down to release the electrical connection.


2021-10-24 045.JPG
Transmission case with the valve body removed.


I very carefully set the valve body on a baking sheet. A new one, I know better than to steal one from the kitchen. (She still hasn't seen the photos of me using the oven to heat the transmission torque converter cover from my Porsche 928S to install new bearings...)
Both the service manual and the Sonnax instructions warn you to take care not to drop or roughly handle the valve body. In English, the TECHM is kinda fragile.

Once at the workbench inside my shop, I placed the valve body in a drain pan, as I figured it would be drooling ATF through this entire process.


2021-10-24 046.JPG
Transmission case side of the valve body. Service manual calls this the 'control valve upper body', meaning the top half of the valve body. Noteworthy items are the seals at the front, seals in the middle, and the two black square speed sensors. To my understanding, those are used to measure input and output shaft speeds of the transmission.

I disassembled the valve body in accordance with the instructions in the Sonnax 6L45-6L90-ZIP kit.


2021-10-24 053.JPG
This is the lower halve of the valve body.
 
OP
OP
skpyle

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
Let me pause the photos for some information:

I bought all the Sonnax parts off ebay. I thought I would not have time to wait for Rock Auto, and couldn't find the pressure switch rebuild kit on Amazon. Turns out, Sonnax, no longer lists the pressure switch rebuild kit 124740-30K. They do still list the tool kit required to rebuild the pressure switches 124740-TL30.

Here are the ebay listings I used to get the ZIP kit, pressure switch rebuild it, and an additional set of pressure switch rebuild seals and discs. The original Sonnax rebuild kit 124740-30K included 40 seals and discs. The ebay kit only includes 5 seals and discs. Which isn't really a bad thing. I later ordered an additional kit of 5 seals and discs to have for the future. I purchased these items through ebay seller 'maxxindustries' based upon their feedback and availability. I was not disappointed, they shipped quickly and were exactly what was stated.

Sonnax ZIP kit:
https://www.ebay.com/itm/254602621595

Sonnax pressure switch rebuild kit and tools:
https://www.ebay.com/itm/254545338132

Additional Sonnax pressure switch seals and discs:
https://www.ebay.com/itm/254602539663
 
OP
OP
skpyle

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
Another note: The Sonnax ZIP kit instructions were good overall, but I felt they were lacking in the individual items done. Thinking about it, the ZIP kit is a collection of shift improvement and fluid correction items all grouped into one kit. So, I searched Sonnax's website and found all the instructions for each individual item. That really clarified things for me.
As well, the video on rebuilding the pressure switches really helped.


Sonnax website, 6L80 page:
https://www.sonnax.com/units/301-6l80

Sonnax 6L80 valve body layout:
https://www.sonnax.com/tech_resources/1052-gm-6l45-6l50-6l80-6l90-valve-body-layout

Sonnax 6L45-6L90-ZIP kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/3505/6L45-6L90-ZIP-IN.pdf?v=1634147559277

Sonnax TCC regulator kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/5074/104740-46K-IN.pdf?v=1587561441236

Sonnax pressure switch rebuild kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/instructions/3767/124740-30K-IN.pdf#in_results

Sonnax pressure switch rebuild kit video: (very much worth watching!)
https://www.sonnax.com/tech_resourc...-gm-6l45-50-80-90-gen-1-6t70-75-transmissions

Sonnax compensator feed regulator valve kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/1705/104740-09K-IN.pdf?v=1613065921470

Sonnax clutch select valve spring kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/1703/104740-02K-IN.pdf?v=1605553741846

Sonnax actuator feed limit valve kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/5073/104740-47K-IN.pdf?v=1587051847015

Sonnax O-ringed end plug kit:
https://d2q1ebiag300ih.cloudfront.net/uploads/part/1707/104740-23K-IN.pdf?v=1617297241349

Sonnax Center Support Seal Kit:
 
Last edited:
OP
OP
skpyle

skpyle

Full Access Member
Joined
May 15, 2021
Posts
393
Reaction score
967
Thank you SO MUCH for sharing your experiencing and making such a thorough writeup. This will be a huge help to many people here, including me. Nice job and I'm looking forward to more info as you're able to share!
You are quite welcome!!! When I mentioned I was putting in the Sonnax parts, you requested I document it. So, I am doing so. Stay tuned...
 

Forum statistics

Threads
128,781
Posts
1,805,301
Members
91,760
Latest member
MyCleftNut

Latest posts

Top