Recent content by lowpost99

  1. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Should have died today...I-75 S in ATL/Marietta at Mount Paran. Swerved suddenly left into the HOV lane to avoid a driver coming into my lane, over-corrected and went across all 5 lanes, hit an Army transport vehicle, bounced off of him, back left across 2 lanes scraped the right of another car...
  2. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Ok maybe I'm crazy... I thought I'd seen and read about an upgrade for 01 NBS Hoes with the ROUND brake booster to a square hydroboost from Cadillacs? I'm not certain what donors, but can someone point me to a write-up on how to do this mod?
  3. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Red fluid dripping from the nose of the transmission...rear seal replacement? Also what years and models Esky's and Denali's center consoles are compatible with my 01 NBS?
  4. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Pics of my Esky cluster as promised....Day and Night. Mnuvv this cluster! New center caps.... I also began removing the side moldings...not too hard used heat gun to soften the glue and got a fingernail behind it, pulled a bit, more heat gun, put on the gloves and then just patiently let the...
  5. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    After searching all last night I found this early this AM. https://www.ebay.com/itm/99-5-02-GMC-Chevy-Cadillac-Silverado-Tahoe-Sierra-Escalade-Cluster-Clear-Lens/283698459062?_trksid=p2485497.m4902.l9144 However....Fools and children.... well I got lucky and didn't have to spend another $25...
  6. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Yeah thats the entire lens. I'm gonna contact them to see if they know where I can get just the clear plastic face cover. It suck that it's not a simple replacement. I was gonna post my Esky cluster upgrade...but no...dice
  7. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Anyone know where I can get the clear plastic for the instrument panels only? Don't want the entire lens, only the clear part that is glued to the top of the speedo. Mine is cracked and looks terrible.
  8. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Or can you just us a bumper cap for an HD instead since it's got that space there already?
  9. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I want to do the 2500 bull nose hood and grill style next for my 01 NBS. I've read that I would need to trim 1" off to fit over the stock bumper OR get the entire HD bumper as well. I also read here in earlier posts that you only need to change the bumper cap with the 45"-50" lower section...
  10. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Thx
  11. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Hey guys, do you clay bar and then wax your truck or should you wax then clay bar?
  12. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Rocket, I wouldn't say I'm the greatest, but I solder electronics boards with an iron and I flow solder usually with gravity on my side by turning parts in weird directions including upside down, and I sweat pipes. Got lucky, I didn't specifically know about the tempered glass, but was just...
  13. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Yeah, that looks like what they must have done. But the situation actually is the same in every case, since the entire metal tab is soldered on directly to the defroster wire pad. During my effort, I pulled it entirely off being a little less accurate with the torch, and had to re-flow the...
  14. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Guys I think soldering was the easist and most effective way to fix this. If you're a bit handy, skip the $40 compounds, and $8 dollar tabs. I used ordinary electrical solder, and a butane torch for the heat. I also noted that the actual tab was also originally solder onto the defroster...
  15. lowpost99

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    x2! Great price!
See more

Forum statistics

Threads
129,117
Posts
1,810,704
Members
92,203
Latest member
firedog9518

Latest posts

Top