Recent content by Erickk120

  1. Erickk120

    2004 5.3 to 6.0 swap

    Don't quote me, but with the exception of the flex plate It should be a bolt on pretty much, If anything you might just want to consider a tune before giving it hell.
  2. Erickk120

    Exhaust Mod Recommendations

    I got the borla pro xs, when I got it originally the main goal was to be able to hear it when I turned the truck on, or when I got on it. Sadly it is still a little too loud for me. Sounds nice and loud on cold starts, while cruising below 2.2k rpms sounds stock. Above that oh boy it gets too...
  3. Erickk120

    Sad front differential??

    The 8.25 is not the strongest ifs diff, so I wouldn't be surprised, give the pinion yoke a spin with the axles disengaged, and without the drive shaft, if you feel any rough spots, or anything not smooth it will probably be your problem. A pitted bearing will do the popping like a bad cv axle...
  4. Erickk120

    Sad front differential??

    Is the drag in any form of 4wd, or just 4hi/4lo? doubt the axles are bad, since you replaced them. If you assembled the engagement portion of the axle the same way it came out, it should be good, unless you just popped the axle and shoved it back in, you can do it on the driver side, but not the...
  5. Erickk120

    4l80e swap - transfer case question

    I'm jealous! If you want to, you can upgrade the stock 3-4 pinion planet from the 246 to a 6 pinion planet, just for the hell of it, can be found under $100 As far as the pump anything even the spacer/shim design will do it, but I'm biased towards the merchant fix, as its fused as an assembly...
  6. Erickk120

    How do I know what size rear pinion flange seal I need?

    I would go with the most expensive choice, even if it turns out to be the same you dont want to be doing that thing again, and check for grooves on the surface of the pinion yoke sealing surface. I my self love the yukon mighty seal for these, it just looks superior. Could be just me but its a...
  7. Erickk120

    2004 5.3 liter tahoe transmission line issue

    It has been a while since I've disconnected those, but you are supposed to install the clips into the fitting, then insert the lines til it clicks/snaps in. That way you dont distort and damaged the retainers. They are a pain to remove but should be a breeze to install. That aside you probably...
  8. Erickk120

    2005 Denali No crank no start

    check battery voltage. Also if you get it running, check what the alternator is putting out and make sure its charging the battery. If below 13v under load then I would suspect bad alternator.
  9. Erickk120

    How do I know what size rear pinion flange seal I need?

    Look at your back diff cover, if you have 10 bolts you have a GM 10 bolt 8.5/8.6 ring gear, if you have 14 bolts you have the 9.5 inch ring gear, the 8.25 inch is the front IFS differential.
  10. Erickk120

    Noticeable difference with Mobil 1 Oil choices?

    wow, I doubt I will ever get past 300k the way I've been driving mine. Currently sitting at 234k
  11. Erickk120

    No heat from front vents

    Same for me, I however have the regular knob, I dont get to see the fancy numbers, My front heat hasnt worked since 2010, I haven't bothered to fix it but I probably have a bad heater, will look into it and report back when I do preventative maintenance on my water pump and coolant.
  12. Erickk120

    Rearend warranty claim (ATK)

    For people that have never done a rear end, I would recommend to get the expensive pinion depth tool, use a gear set from motive/richmond/US gear, but dont get the cheap ones, get the good ones and use the depth they recommend stamped in the pinion head with the depth tool, set backlash/preload...
  13. Erickk120

    Getting new rear axles - should I change from Gov bomb to Truetrack?

    I installed a reman g80 on mine as I dont really beat on it much. Once I get a new engine with mods I will prob replace it with a true trac, for the time being I'm happy with the Gov bomb.
  14. Erickk120

    NP241 swap

    My 241 has the other style flange, I'm ashamed to admit I've been riding without a front prop shaft for the last good part of a year. Whats the part number for the pig tails, I broke one of the tabs on mine and its barely hanging there.
  15. Erickk120

    Is it possible?

    If they are both 246s you can just swap the front input shafts from your 32 spline to your 27 and be good. I had to do this on a 241 which had a 27 and i needed a 32 for my manual transmission swap. Tear down is pretty easy on these units, just put everything back together, and might as well...
Top