2003 Tahoe 5.3 VIN-Z - P0300 With a Twist

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
M

mridgewayii

TYF Newbie
Joined
Apr 21, 2022
Posts
11
Reaction score
10
SWAG I wonder if the O2 heater circuits are working. If not, it could prevent the sensors from coming alive. But I think there's a code for that. (?)
I agree and I thought that in the beginning but after driving it 10-15 miles … I would think the O2 sensors would have been hot enough
 

Tonyv__

Full Access Member
Joined
Apr 18, 2018
Posts
2,675
Reaction score
5,349
Location
Bucks county PA
Well, your post made up my mind. I’m going to pull the valve covers this week to see. I’m pretty competent at troubleshooting and can’t remember a time something had me this stumped. Time to go back to the basics and see if the mechanical parts are working.
Keep us updated and good luck
 

Fless

Staff member
Super Moderator
Joined
Apr 2, 2017
Posts
10,606
Reaction score
21,118
Location
Elev 5,280
I agree and I thought that in the beginning but after driving it 10-15 miles … I would think the O2 sensors would have been hot enough

Think, but know. I'd be testing the heater circuits to make sure they can carry the load. Several YouTubes out there showing how using a test light that draws some current.
 

Mudsport96

Full Access Member
Joined
Jun 6, 2020
Posts
1,205
Reaction score
1,866
Location
40.923,-89.488. Illinois
If you can get a helper looking at moving rockers is easier.
Remove coil packs and valve covers and pull the fuel pump relay. Have helper crank the engine while you watch rockers. Look for any that aren't moving a whole lot, or seem to have slop. Otherwise, use a socket and breaker bar to rotate and check for slop in the rockers.
 

V327839

TYF Newbie
Joined
May 22, 2021
Posts
28
Reaction score
24
I had an intermittent limp mode issue for the longest time. I could even fix it just by slamming the drivers door on occasion. Since you’ve done so much work to your engine, I would check the place I found my problem. The underside of the main harness as it crosses the intake manifold. In my case, the engine cover has squashed some wires to the point I had a bunch of shiners. After some wire repair, the issue was fixed. It’s worth a shot as I found that the main harness as it’s pulled across the manifold is very tight and rubs in several places, especially if you’ve moved it yourself. You’ll never get it back perfect. Thats my experience.
 
OP
OP
M

mridgewayii

TYF Newbie
Joined
Apr 21, 2022
Posts
11
Reaction score
10
Hi Everyone
Thought I would provide an update. Pulled the valve covers and lifters were fine. Ran a compression check and all were even except #5. #5 was higher and the more I cranked the higher it got. We all know that’s not how it is supposed to work.

Pulled the engine this weekend. Has to be a cracked head as the #5 exhaust valve was severely rusted. The Tahoe has been losing coolant over the years but very, very minimally. Maybe a half quart a year? I chalked that up to being in a very dry climate but guess I was wrong on that one.

As info - these were 862 head castings and NOT the Castec version (or at least it didn’t have the typical castec head markings.

5.3 is staying out and picked up a 150K mile LQ4 6.0 core today. I’ll be rebuilding it and breathing new life into the old girl.

Thanks for everyone’s input and suggestions.
 

Forum statistics

Threads
129,618
Posts
1,819,023
Members
92,895
Latest member
804getSome

Latest posts

Top