Search results

  1. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Forgot to update last week. New motor is in, just needs to be hooked up. Glad I went through all the hassle of painting the block, it really shows (see image three) gotta wait for my buddy’s schedule to line up with mine to get it closer to done. But it’s in!
  2. MadDogDelpho

    Will the Silverado front seats and jump seat bolt in a Tahoe?

    That’s outside my realm, bud. The old seats may have had a weight sensor or something that the Tahoe seats don’t? I’m unfamiliar with the system, I just did the sensor-less center console myself
  3. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    It pulled the old assembly alright at that setting. Had to put it there to get past the bumper, but I might pull it as well for ease of install and set the crane for 1/2 ton
  4. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Been a minute, fellers. Bought an engine and transmission early last year to freshen up the Tahoe, and shortly after I lost third and fourth gear. So she’s been parked up while I fix up the replacement. Put a Truck Norris in the motor after getting it cleaned up at the machine shop and threw a...
  5. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    True, they were Timken hubs as a matter of fact
  6. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I definitely stretched it. The RF upper ball joint has been clunking for about a year. New uppers are specifically designed for a 2-3” lift so should last much longer
  7. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Well, yesterday and today. Rebuilt my WHOLE front end. I had torn bushings, tie rods, ball joint boots, CV axles, everything. About 4 years and 40-50,000 miles since I put a Detroit axle front end kit on, so that’s a good ballpark for that budget-minded kit
  8. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Not sure if this is the best thread to ask in, but does anyone have any leads on where to get longer sway bar links? I’ve got a 3/2 level and I’ve noticed the stock links seem to cause my inner tie rods to rub against the sway bar. I need maybe an extra inch of clearance is all
  9. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Re-pinned the connector (I had the hot wire in the wrong spot) and now it works like a charm! Apparently all these basic motorized seats need is a power and ground.
  10. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Yeah, definitely been quite a while, I missed you guys!
  11. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Very long time, no post. The motor went out in my driver’s seat a while back so I’m trying to swap in some inexpensive seats from an ‘03+ To my ‘02 but having difficulty figuring out the wiring. So I’ll be nice and close to my steering wheel until I get it figured out!
  12. MadDogDelpho

    HD Hood Swap

    Pretty positive the one I got is aftermarket. Drove to Houston to get it, but it was in primer and the gaps are slightly bigger than the factory hood, but anywhere further than 5 feet and you can't tell
  13. MadDogDelpho

    07burb’s 1991 GMC R3500 Crew Cab Dually

    Love it. I need to get some free time to work on my pile
  14. MadDogDelpho

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I'm not dead, I promise. Just too busy with school and work to afford any free time that isn't sleep. Still enjoying it though!
  15. MadDogDelpho

    *WIN $200* Truck of the Quarter/TOTQ - Submissions for 1st Quarter 2018

    I think I’ll try out for this round. The big girl needs a bath :(
  16. MadDogDelpho

    --- Photos: SPOTTER'S THREAD (post up all years/models) ---

    Right on. I appreciate it brother
  17. MadDogDelpho

    Mad Dog’s 85 Burb

    im back boys, and better than ever. Finally finished the paperwork and everything on this plush 1985 GMC Sierra Classic Suburban. 350/350, 12 bolt rear, dual front shocks, tilt steering, power windows, ac... and just a hint of rust. Right now we’re calling her The Beast. Got a lot of work to do...
  18. MadDogDelpho

    Blurred's 04 Tahoe Z71 build - Mr. Greenly Greenerson

    I think @Rocket Man has the same color code and did his Denali, he might know. Also pulling the bezel is super easy. Just tilt the column down, put ‘er in 1st, and just pull around the edges of the bezel and it’ll come off. Or did you mean the full dash? Because that one I don’t know off the top...
  19. MadDogDelpho

    Pete's (Now Nate's) 2003 Denali Budget Build thread

    Idk Pete, they’re pretty nice...
  20. MadDogDelpho

    --- Photos: SPOTTER'S THREAD (post up all years/models) ---

    You know it. For some reason the PO had the driver’s side one, but not the passenger side? Gonna order a new one soon. Also, does anyone with any squarebody experience know where to get rear door cards? LMC only sells new fronts and the rears have seen better days.
  21. MadDogDelpho

    --- Photos: SPOTTER'S THREAD (post up all years/models) ---

    Spotted some new taillights on the finally mine 1985 GMC Suburban
  22. MadDogDelpho

    --- Photos: SPOTTER'S THREAD (post up all years/models) ---

    Gutted, but came with most of the interior parts. A little rust in the passenger floorboard that needs to be fixed before a rebuild. I’m pretty sure it was a High Sierra, has vinyl seats, AC, 12 bolt rear, dual shock front, and automatic locking front axle.
  23. MadDogDelpho

    --- Photos: SPOTTER'S THREAD (post up all years/models) ---

    Spotted my new 85 Burb in my driveway this morning. Got dropped off late last night.
  24. MadDogDelpho

    --- Photos: SPOTTER'S THREAD (post up all years/models) ---

    LTZ? Or just a Z71 with chrome rims?

Forum statistics

Threads
128,800
Posts
1,805,626
Members
91,784
Latest member
navyboy14094
Top