Search results

  1. vt_hokie2008

    LED headlights

    How's the light output with the Morimoto 2Stroke 2.0? I'm looking at maybe trying them out
  2. vt_hokie2008

    Brake Pads

    I'm still running the pads 20k miles later and they still turn my wheels gunmetal in under 2 weeks every time. They brake well though.
  3. vt_hokie2008

    Anyone running Spyder headlights with LED's for a 07-14 Tahoe?

    That sucks. I hate to do an actual retrofit since VA police will write you for "improper equipment" for anything that isn't factory, so I'd rather put less into it if I end up having to remove it.
  4. vt_hokie2008

    Anyone running Spyder headlights with LED's for a 07-14 Tahoe?

    What did you end up going with? I'm in need of new headlights (fogged over on the inside) and would prefer to buy an upgrade vs replacing with stock.
  5. vt_hokie2008

    Brake Pads

    My AC Delcos on the rear don't dust at all, but wasn't sure if the fronts would be the same story. Thanks for the input everyone! Sent from my SM-G935V using Tapatalk
  6. vt_hokie2008

    CCM & Terra Grapplers done

    I've now put 30k on these and they've got at least 20k to go, lots of tread left. The only downside so far is my mpg's dropped 2mpg on hwy. Not sure if that's from the tires ir the leveling kit or both. I'm only getting 17.5 hwy now, and that's after the BlackBear tune (which makes the vehicle...
  7. vt_hokie2008

    Brake Pads

    My stock pads/rotors on the front were replaced awhile ago with r1 concepts rotors (stock ones were warped) and Hawk pads. The Hawk pads put off a TON of dust and just didn't brake well until you warmed them up quite a bit, so I swapped them out for EBC Greenstuff pads at the recommendation of...
  8. vt_hokie2008

    Aftermarket backup camera on applique with or w/out OEM cutout

    That's how mine is Sent from my SM-G935V using Tapatalk
  9. vt_hokie2008

    Headlight control sensor

    That would be excellent Sent from my SM-G935V using Tapatalk
  10. vt_hokie2008

    Headlight control sensor

    I'm having a hard time finding a part number for it. My headlights are on 95% of the time, so I want to replace the light sensor on the dash. Anyone have a part number for it? 2007 Tahoe
  11. vt_hokie2008

    I installed a avic-8200nex with idatalink gm5 but cant get calls to work

    They said the 4100nex doesn't fit either b/c of a dash brace in the rear, but it can be cut out to make it work. Sent from my SM-G935V using Tapatalk
  12. vt_hokie2008

    NNBS Driver Side Mirror

    Is the glass free from scratches? If so, I'll take it Sent from my SM-G935V using Tapatalk
  13. vt_hokie2008

    NNBS Driver Side Mirror

    They're only power adjustable, not power folding. Sent from my SM-G935V using Tapatalk
  14. vt_hokie2008

    NNBS Driver Side Mirror

    Still have this? Since you haven't installed it, I don't imagine you can answer this, but does the glass wobble? My driver side is shaking when at interstate speeds and it's driving me crazy.
  15. vt_hokie2008

    I installed a avic-8200nex with idatalink gm5 but cant get calls to work

    My 4100NEX mic is on the rear of the light fixture in the center, picks me and others up pretty well. Definitely has road noise in it at highway speeds though for the recipient of my call.
  16. vt_hokie2008

    Aftermarket backup camera on applique with or w/out OEM cutout

    Late on this, but unless you plan on getting the OEM camera, get the one without the cutout. My aftermarket one mounts with screws to the bottom of the applique
  17. vt_hokie2008

    How to: DRL with Parking lights

    I assume both will flash for signal if I just use a wire? I'd like drl and park light to be on together for DRL duties and have both flash for signaling. Both on with headlights is fine too. This is definitely easier than jumping wires on the harness behind the headlights. I did that for...
  18. vt_hokie2008

    Warped rear rotors???

    I replaced my front, badly warped stock rotors and pads with R1 Concepts rotors and Hawk HPS pads 3 years ago and now I'm feeling the familiar shaking when braking. The steering wheel isn't doing any shaking at all, so I assume it to be the rear rotors that are warped. I'm thinking about the...
  19. vt_hokie2008

    Supercharged Tahoe TBSS

    Those look fun
  20. vt_hokie2008

    How to install DDM HID kit on low beams w/ relay harness

    It's just a possibility that it may not handle it. I think people have run it without and been fine
  21. vt_hokie2008

    How to install DDM HID kit on low beams w/ relay harness

    You "can" just plug and play, however you're more prone to having bulbs not fire on the first try and run the risk of pulling too much current through the factory wiring (burning it in two or worst case, starting a fire from the hot wire). The power/ground/fuse pull directly from the battery...
  22. vt_hokie2008

    Pioneer 4100NEX installed

    Unfortunately all of this info isn't well documented anywhere, so I happened to stumble upon it. Metra phone support is actually pretty knowledgeable too. Sent from my SM-N900V using Tapatalk
  23. vt_hokie2008

    Pioneer 4100NEX installed

    Yep, the app is much easier to assign buttons. I think it's android only and requires an OTG cable: https://www.amazon.com/dp/B00B4GGW5Q/ref=cm_sw_r_other_awd_sbD5wbHWKS1NF You plug that cable into your phone, then plug a micro usb cable into that cable and into the Axxess unit (if I'm...
  24. vt_hokie2008

    Pioneer 4100NEX installed

    I assigned a button to the microphone and it works fine. I used the one that looks like a person's face. I made up/down arrows next/previous track and don't really remember what I did with the others (apparently I don't use those enough to know) Sent from my SM-N900V using Tapatalk
  25. vt_hokie2008

    Pioneer 4100NEX installed

    If you're using the Axxess module I highly recommend the smartphone app, makes setting it up much much easier. Mine stopped working for a but and I recrimped the connection to the steering controls wire and it's been fine every since. I'd like to go back and solder some of my connections (such...

Forum statistics

Threads
129,271
Posts
1,813,088
Members
92,379
Latest member
Pepper1700

Latest posts

Top