I checked everything the only I found was the #2 injector harness appeared to be loose for some reason. No damage to the wiring anywhere. I have driven it about 100 miles and the light didn’t come back on. Very odd.
I was driving home from the grocery store tonight and idling at a light the check engine light came one followed by a message that said low engine power mode or something similar. The traction control disabled message followed. It was in limp mode took a while to make it to 35 mph. I used my...
Just to update and close this one, i turns out my replacement was defective as well. I bought a scanner and identified the passenger side sensor and bought a new replacement. Issue solved.
Thinking about this, my old scanner (an Innova scanner with abs reader) didn't read a code either after I cleared the original speed sensor. The light doesn’t come o. Until I start the truck. I wonder if I need to scan with the truck running?
I have not bled the brakes. My new XTool scanner doesnt show any abs codes for some reason. I will try it again this weekend. In the meantime, the brakes function without issue and the pedal feels fine.
The abs light is on as well. You described the exact scenario that happened with me. I forgot to pump the brakes before putting it in gear. So i should try some emergency stops?
So i have been thinking about this. Could there be air in the line/abs controller from compressing the brake caliper pistons somehow? The passenger side pads installed without issue. When i installed the drivers side pads last weekend, i compressed the caliper pistons and it caused fluid to...
I am looking to purchase a new scan tool to help diagnose the issues I am having with my ABS and SRS. Does anyone have any experience with these? I an looking to stay in the $300 range. The XTool Inplus looks nice. Any have any suggestions?
When I scanned for codes there weren’t any. There was originally a right front wheel speed sensor circuit malfunction code (C0040). I cleared that code last weekend when I installed the new sensor. I drove the truck approximately 100 miles last week then swapped the hub. I then checked for any...
So I i stalled the new hub today. The old one definitely needed replacing as you could here the bearings rattling. I also installed the new pads. The old pads were just a hair away from the warning tabs. The brake feel is lot better. The Moog hub had the speed sensor installed so I didnt have to...
After doing some additional research I believe it is the hub. I can get the Moog hub here by Friday so I plan to get this one, the AC Delco will not arrive until Monday...
Good advice! How much play should the sensor have? The original sensor had separated in the hole, I had to pull the outer plastic on the part in the hub out separately.
I did find this tech bulletin that was refered to on another site for this issue. #03-05-25-007C
It says if the speed sensor mounting surface isn’t throughly cleaned it can cause a gap issue. I am going to give this a try when I replace the pads.
I hope not as this sounds like a pain in the ass and i don’t work on electronics. Also i don’t see how compressing the brake caliper would cause this all the sudden.
So I have been dealing with issues that came up in rapid succession. I had a front ABS sensor that went out. Today I swapped that out with the correct AC Delco part. While changing this one out I noticed that the pads needed to be changed so I plan on doing that next weekend. While changing...
I have a service air bag light that came on a couple of weeks ago as well as the service air bag message. Last time this happened several years back it was a front impact sensor. So I swapped the two sensors out one at a time with my replacement units but it didn't solve the problem. My code...
Which one should I use?
PAC GM1A-RST RadioPRO Advanced Interface for GM Vehicles
Or
PAC RP5-GM11 Radio Replacement Interface.
I have a 2005 Tahoe with the Bose system with RSE. I currently have the factory navigation unit installed. The truck originally had the non-navigation unit from...
Parts came in yesterday. I was able to fix it today. I tapped on the motor with a hammer and it went back up enough for me to easily reach the bolts to loosen it from the window. I went ahead and replaced the regulator and the motor. The motor seemed to be the issue as the regulator was fine...
I believe it is the switch, i have a replacement at home that i can try on it. I just have basic hand tools with me at work so i cant check it to make sure. The other windows still go up and down as well as the door lock.
Where exactly is the scree on the switch or the trim?
So i get to work this morning, roll my window down to enter the parking garage and now it will not go back up and of course it is raining today. Anyone have any tips on how to roll it back up? Yesterday it didn’t want to go down on time. I tried again and to worked fine. I thought it was a...
So after having a tire issue on the road for the first time since owning my Tahoe I have decided that i need to carry a better lug wrench with me in the truck. I was thinking just a craftsman breaker bar and extension. Does anyone have any recommendations on a lug wrench to carry with me? I like...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.