Recent content by TigerEyz3

  1. TigerEyz3

    Suspension swap

    As long as the distances and clearances allow, I see no reason why you can't do what you want. That said, I think the NBS (GMT900) trucks use a rack-and-pinion setup rather than a draglink like our OBS (GMT400) trucks.
  2. TigerEyz3

    Leaf spring bushing replacement advice

    You have to remove the leaf springs to access the bushings (the spring eye fully covers them). You have to drop the fuel tank on the driver side to access the hanger bolt.
  3. TigerEyz3

    Polyurethane leaf spring bushings or not?

    As Swathdiver said... polyurethane is known for squeaking. Lube well and you'll be fine (re-lube when squeaks occur).
  4. TigerEyz3

    Should I buy a full exhaust?

    I'm a Magnaflow fan (over Walker). Material quality and reviews seem to be a bit better.
  5. TigerEyz3

    will 265/65 R18 tires fit a stock suspension 97 Tahoe?

    All day... that's a roughly a 31.5" x 10.5" tall tire. Basically it's an optional factory tire diameter. Assuming your 1997 is a 4x4 with non-sagging suspension, you should be fine. My Tahoe (effectively with a 1" drop... 2" spindle drop + 1" coil spacer) previously had 265/65/17 without any...
  6. TigerEyz3

    Rust prevention

    There's a product that's similar to Fluid Film called NH Oil Undercoating. Based on videos I've seen, it's preferred over Fluid Film - better scent and "re-blacks" the underside/coated surfaces. Check out https://nhoilundercoating.com/
  7. TigerEyz3

    Window deflectors

    These are all from the driver side...
  8. TigerEyz3

    Window deflectors

    I know this may be a bit late, but I've got WeatherTech in-channel deflectors... no problem with the clips holding them in, it's a press-fit. Prior to the WeatherTech's, I had the AVS ones that tape to the metal/paint of the door above the windows.
  9. TigerEyz3

    Tahoe Frame Rust

    Can't say the are "known" for rust, but environment plays a huge part... salt + moisture + steel = rust Not sure if that helps your decision making process, but it's the reality of metal. There's a company out called NH Oil Undercoating that makes a product that works to inhibit/stop the rust...
  10. TigerEyz3

    CB Antenna

    Don't have a good pic of my mount, but I drilled a hole in the roof (over the cargo area). This location gives a great ground plane, with just a bit of forward bias.
  11. TigerEyz3

    Looking for LED Headlights

    Late to the party here, but would highly recommend that you do your research before purchasing. All LED bulbs are not good bulbs...and truthfully, the good ones are going to cost you some decent money. That said, take a look at www.headlightrevolution.com The Supernova v.4 LED bulbs are VERY...
  12. TigerEyz3

    14x1.5 Low Profile Lug Nuts

    Your spacer (wheel adapter) should be 1.5" or more to clear the lugs with no issue. Assuming the adapters you purchased are less than the 1.5"and that you're wanting to keep the adapters you purchased, you'll have to cut the lugs to be shorter (not recommended practice).
  13. TigerEyz3

    Radiator Change

    Check out Radiator Express... http://www.radiatorexpress.com/part-lookup/radiator/gmc/2004/yukon/denali/60l-v8 Personally recommend them. If you've got the extra coin, go for the all aluminum variety with the greater cooling capacity. Also as stated previously, get the two cooler option, if...
  14. TigerEyz3

    Any one have a Jotto Radio Console with a Hoe's stock console too?

    Didn't use a Jotto, but many years ago I installed a radio console (purchased off of ebay) between the dash and factory console. The factory console had to be moved rearward a bit for it to fit. Couldn't tell you the name of the radio console, but it used to be used in patrol vehicles - all...
  15. TigerEyz3

    Getting my 1996 Yukon back on the road

    Could be as simple as distributor being 180* out... Though unlikely if you followed the spider numbers, it could be that one or more injectors are in the wrong cylinder.

Forum statistics

Threads
128,781
Posts
1,805,301
Members
91,760
Latest member
MyCleftNut

Latest posts

Top